Previous Thread
Next Thread
Print Thread
Rate This Thread
Hop To
Page 1 of 3 1 2 3
#4558448 - 03/03/21 04:09 PM 1:32nd scale Fokker D.II  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
I'm still waiting for the figures to arrive for the Roland D.VI so I can complete that model.
In the meantime I'm starting on the 'Special Hobby' 1:32nd scale Fokker D.II.
This model will represent a Fokker D.II, serial number not known, that was attached to ‘Kampfeinsitzer Stafflen’ (Kesta) 4b sometime between April 1917 - October 1918 at Royal Bavarian AF, Freiburg.
Should be fun,

Mike

[Linked Image]

[Linked Image]



[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4558648 - 03/04/21 07:56 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2013
Posts: 400
loftyc Offline
Member
loftyc  Offline
Member

Joined: Dec 2013
Posts: 400
wing-warper still in use in late 1918? I guess the back areas weren't a high priority. or a medium one.

#4558660 - 03/04/21 11:19 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Mar 2011
Posts: 594
VonS Offline
WWI Flight Sims on a Mac
VonS  Offline
WWI Flight Sims on a Mac
Member

Joined: Mar 2011
Posts: 594
I've always liked the looks of the Fokker D.I to D.V series, so I look forward to developments with this model in particular.

@Lofty, yes I was surprised too, to read that defense units had such warpers even as late as '18. Then again, there were a few dozen or so late Alb. D.IIs in front-line service until the end of the war - so perhaps I shouldn't be surprised by warpers in use by home defense. The lovely Fokk. D.V I think also served briefly in defensive roles, and maybe very briefly on the front too - although there's some debate on whether or not the D.V was used as a fighter.

Happy flying and wing warping,
Von S smile2


// See WOFF on a Mac post for installation instructions regarding WOFF UE/PE/BH&H2 on Macs (https://tinyurl.com/WOFFonMac) // VonS WOFF/WOTR mods. are tweaks of files that are © OBD Software. // FE2 Tweaked FMs & Realism Pack (https://tinyurl.com/FE2fms) // FE2 Representative Vids. (https://tinyurl.com/fe2onamac) //
#4558887 - 03/06/21 09:19 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
Just a quick update.
The engine and propeller are finished.
The basic cockpit is also finished, but without any added detail, such as control cables, bracing wires and pipes etc.
This is because for the first time, I'm add a pilot figure into the cockpit.
With the pilot located, just about everything in the cockpit is hidden from view, except for the top of the control column and the one instrument.
The figure I'm converting for this model is from 'Wings Cockpit Figures.

Mike

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4558934 - 03/07/21 04:30 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
The pilot figure started off as the ‘Wings Cockpit' figures - seated LSK pilot (LSK 04A).
Some heavy modification of this figure was necessary in order to get it to be able to fit into the cockpit of the closed up fuselage.
Basically material had to be removed from the legs and torso, with the arms pinned into their sockets and re-positioned.
Any gaps were filled with modelling putty.

Mike

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4558937 - 03/07/21 04:40 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Aug 2010
Posts: 6,267
carrick58 Offline
Hotshot
carrick58  Offline
Hotshot

Joined: Aug 2010
Posts: 6,267
A wonderful subject The Fokker D II - D V.

#4558938 - 03/07/21 04:53 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Jul 2012
Posts: 2,494
Adger Online smile
Member
Adger  Online Smile
Member

Joined: Jul 2012
Posts: 2,494
Excellent stuff Sandbagger, The models shown on your website are quite brilliant mate, I’d recommend anyone to have a look at Mike’s models ..outstanding.


They shall grow not old, as we that are left grow old:
Age shall not weary them, nor the years condemn.
At the going down of the sun and in the morning
We will remember them.
#4559027 - 03/08/21 10:00 AM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Thanks guys,

Mike


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4559035 - 03/08/21 11:44 AM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Mar 2020
Posts: 293
Albert Tross Online content
Flight Sim Nut
Albert Tross  Online Content
Flight Sim Nut
Member

Joined: Mar 2020
Posts: 293
UK
Agreed, the models are brilliant, very realistic. I particularly like the more unusual models too.

This latest one is a curious bird, still using wing warping and a very outdated engine. I remember seeing a picture of Ernst Udet's one with a cutout of a second person attached to the fuselage to make it look like a two seater....crazy stuff.


"A great deal of an aeroplane could be holed without affecting its ability to fly. Wings and fuselage could be—and often were—pierced in 50 places, missing the occupants by inches (blissfully unaware of how close it had come until they returned to base). Then the sailmaker would carefully cover each hole with a square inch of Irish linen frayed at the edges and with a brushful of dope make our aircraft 'serviceable' again within an hour."
#4559137 - 03/08/21 11:39 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Oct 2020
Posts: 101
trustworthykebab Offline
Member
trustworthykebab  Offline
Member

Joined: Oct 2020
Posts: 101
Looking forward to this one wink

#4559141 - 03/09/21 01:45 AM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Mar 2011
Posts: 3,175
Rick_Rawlings Offline
Senior Member
Rick_Rawlings  Offline
Senior Member

Joined: Mar 2011
Posts: 3,175
Top-notch work as always!


The older I get, the more I realize I don't need to be Han, Luke or Leia. I'm just happy to be rebel scum...
#4559656 - 03/12/21 09:40 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
Just an update on this build.
The fuselage is closed up now and prepared as far as it can go at this stage.
Being a 'Special Hobby' kit there was some work to do as expected.
The machine gun location required modification so the replacement 'GasPatch' weapon can be fitted.
All of the rigging points needed to be drilled using either a 0.3 or 0.4 mm diameter drill.
The rudder and elevator control cable ports in the fuselage needed drilling out and oval shaped.
Holes were drilled into the fuselage sides for what appears to have been transportation posts, used to secure the wings to the fuselage.
These posts were also fitted to the lower wings.
The lower wing 'spar' is very flimsy causing the wings to flap like a demented chicken every time the wing was handled.
To reinforce the wing to fuselage joint, I added a styrene block into the wing locating slot and onto the underside of the cockpit assembly.
This should make the wing to fuselage joint stronger.
There is also a flight control lever and cable on the underside of the fuselage which is not included.
This is similar to that of the Fokker Eindeckers and I believe is part of the elevator control run.
I've created slots for both the lever and cable.
I've also drilled and pinned the landing gear struts as originally they were intended to be 'butt' joints (never a good thing).
The strangest change was needed to align the engine cowl to the two fuselage side panels.
The kit instructions tell you how this can be done, which raises the question as to why the parts were not molded to align in the first place?
Anyway I ignored their instructions and as Frank would have said 'I did it my way'.

Mike

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4560444 - 03/17/21 08:37 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
I've now painted the basic colour scheme for this aircraft.
I still have to seal and apply weathering, streaked decals etc.
I decided to create masks for the crosses as the kit supplied decal are not good,

Mike


[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

Last edited by Sandbagger; 03/17/21 08:48 PM.

[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4560771 - 03/20/21 11:22 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
The 'Aviattic' clear linen effect and streaked decals have been applied.
I still need to clear coat and weather the surfaces.
Also I've made the tail skid assembly from micro-tube as the kit struts were very weak.
I had to shorten the actual skid as well as it was way too long.

Mike

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4561209 - 03/24/21 07:57 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
A few updates for the Fokker D.II build.
The pilot figure has been painted and is fitted into the cockpit.
Also the engine is now fitted.
The general weathering is a combination of 'Flory Models' Dark Dirt fine clay wash and 'Tamiya' Weathering Master Set A (Mud).
The engine exhaust and oil erosion on the fuselage forward side panels is 'Tamiya' Flat Aluminium (X16) stipple brushed over the green.
Then the same 'Flory Models' wash dabbed into the Aluminium painted surface.
The same technique was used for the doped linen erosion on the forward streaked decal area, but for that, 'Tamiya' Deck Tan (X55) was stippled on before the 'Flory' wash was applied.
'AK Interactive' Engine Oil (2019) was brushed at the outlet of the side panels and under the forward fuselage.

Mike

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4561211 - 03/24/21 08:06 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Jun 2012
Posts: 7,748
Robert_Wiggins Online smile
BWOC Survivor!...So Far!!
Robert_Wiggins  Online Smile
BWOC Survivor!...So Far!!
Hotshot

Joined: Jun 2012
Posts: 7,748
Lindsay, Ontario, Canada
I really like the paint scheme and the weathering on this model!!


(System_Specs)
Case: Cooler Master Storm Trooper
PSU: Ultra X3,1000-Watt
MB: Asus Maximus VI Extreme
Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered
CPU: Intel i7-4770K, OC to 4.427Ghz
CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler
Vid Card: ASUS GTX 980Ti STRIX 6GB
OS and Games on separate: Samsung 840 Series 250GB SSD
Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L
Periphs: MS Sidewinder FFB2 Pro, TrackIR 4

#4561212 - 03/24/21 08:16 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: May 2016
Posts: 1,020
BuckeyeBob Offline
Member
BuckeyeBob  Offline
Member

Joined: May 2016
Posts: 1,020
Ohio, USA
As do I. Bravo!

#4561330 - 03/25/21 08:05 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
The single ‘GasPatch’ early LMG ‘Spandau’ 08 has been fitted.
This required modification of both the gun and fuselage decking panel.
I used the 'GasPatch' ammunition belt instead of the kit supplied photo-etch part.
I also had to scratch the empty ammunition belt chute as the kit does not include the chute?
The eight 'transportation' posts have also been added to the fuselage sides and lower wings.

Now onto the struts then pre-rigging,

Mike

[Linked Image]

[Linked Image]

[Linked Image]

Last edited by Sandbagger; 03/25/21 09:33 PM.

[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4561414 - 03/26/21 05:56 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Jul 2012
Posts: 2,494
Adger Online smile
Member
Adger  Online Smile
Member

Joined: Jul 2012
Posts: 2,494
Looking incredible already Mike, brilliant stuff.


They shall grow not old, as we that are left grow old:
Age shall not weary them, nor the years condemn.
At the going down of the sun and in the morning
We will remember them.
#4561538 - 03/27/21 11:50 PM Re: 1:32nd scale Fokker D.II [Re: Sandbagger]  
Joined: Dec 2000
Posts: 6,441
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 6,441
Coningsby, Lincs, UK
Hi all,
Just a quick update.
Looking at photographs it's difficult to see detail for the interplane struts on this aircraft.
Some look to be of wood construction only.
Others seem to show a tubular reinforcing tube that was fitted to the leading edge of each strut with wood aerofoil struts attached to its rear edge.
Also what appears to be four 'wrappings' of either linen or metal around each strut.
Normally strut wrapping would be linen and these were used to help prevent the wood struts from splitting under stress.
Anyway, the kit 'wrappings' were over sized so I decided to modify all eight struts.
The 'wrappings' were sanded off and the leading edge tubes, which are not represented on the kit struts, were scribed.
Base coated with 'Tamiya' Deck Tan (XF78), then clear coat sealed.
The wood areas were masked off and 'Alclad' Steel (ALC112) was airbrushed over the tubes.
Clear coated again then 'Flory Models' Dark Dirt clay wash applied.
Clear coated yet again and 1 mm wide strips were applied from the ‘Xtradecal’ Parallel Stripes (White XPS2) set.
A final clear coat was then applied to seal everything.
The cutout in the two inboard, rear interplane struts, are to allow the wing warping control lines to route from the fuselage to the outboard struts.

Mike

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
Page 1 of 3 1 2 3

Moderated by  Polovski 

Quick Search
Recent Articles
Support SimHQ

If you shop on Amazon use this Amazon link to support SimHQ
.
Social


Recent Topics
I'll be damned !!
by NoFlyBoy. 05/11/21 07:13 PM
RM Jet Suit Boarding
by Red2112. 05/08/21 02:07 PM
Idiot for the day
by rwatson. 05/07/21 10:55 AM
The cost of Epic free games
by Blade_RJ. 05/06/21 08:28 PM
That mettalic smell you feel is actually yours !
by Blade_RJ. 05/06/21 05:15 PM
Shiny American Rocket, cheaper by the dozen
by Nixer. 05/06/21 12:48 AM
House of the Dragon
by PanzerMeyer. 05/05/21 05:45 PM
Some funny Facebook observations
by PanzerMeyer. 05/05/21 11:53 AM
Chinese Rocket
by carrick58. 05/05/21 12:26 AM
Hope everyone is having a good day
by oldgrognard. 05/04/21 02:09 PM
Powered by UBB.threads™ PHP Forum Software 7.6.0