My engine control unit and mechanization

My engine control unit and mechanization

Nice job.

Thank you!

Thanks !.
The clutch consists of felt washers pursed bolts.

Troll,

See more pictures here: http://forum.il2sturmovik.ru/topic/2996-rud-svoimi-rukami-ishu/

GVL224, besides this throttle version you sold kits of metal parts plus the sensor (for analog USB controller)?

Maybe I did not quite understand the question ...
On the mechanics of iron can be installed as an analog magrez and any other using the appropriate controller.

Relative the sensor, some like Mega_Mozg "MMSens" TLE5010, VKB "MaRS", work in digital mode, so need compatible USB board.

I want know if your sensor (KMZ41?) will work with BU0836 board (common board for DIY people), wired as conventional (analog) potentiometer with 3 wires: +5V, Signal, Gnd.

And if you sold only the sensor and metal laser cut parts for assemble the mechanics - to make shipping more affordable.

I bundled mechanics analog magrezami (KMZ41) and controllers MJ16, GVL224_4096-8 which are applied in the BRD mechanics.
Dimensions of mounting sensors like the BRD and the VKB.

This is a work of art...well done.

I bring to your attention the iron mechanics (KIT kit) to build dashboards engine (s) and other mechanization (flaps radiators, shields, etc.). Mechanics offers not painted and assembled. Paint and (or) assembly discussed separately.

His mechanics I conditionally divided into three types (differences in the arms):
- For ore - $ 17;
- For the propeller pitch - $ 16;
- For the other axes "Universal" - $ 15.

Mechanics has several customization options deflection angles of levers:
1. symmetrical (the same amount of deviation from the vertical "self" and "away"): 40 (+ -20) degrees. and 76 (+ -38) degrees.
2. not symmetrical (myself more on smaller or turnover): 57 (20, -37) or (+37; -20) degrees.
These angles are set by tightening bolts (they also serve as travel stops), in the following cases need to change the angle of stroke mechanics, this procedure takes 2-3 minutes and is performed by permutation of tightening screws in the other holes.

As sensors may be used on an axis:
1. do not require the adaptation:
- MagRez from BRD (my build);
- RAMS from Komaroff;
- MARS from VKB;
- A variable resistor using a special plate, the clutch and the longer mounting screws (option kit).
2. They need to be adapted:
- All you want from what is used in the construction of joysticks! eg HH, optical sensors, and other sensors.
Screws for mounting the sensors are arranged on the same axis with the axis of the lever at an equal distance apart, the distance between the screws 34.4 mm.

Electronics (controllers) can use any ...
I suggest:
- GVL4096 - 24-27 dollars;
- MDzhoy16 - 18-22 dollars;
- MDzhoy8 - 14-18 dollars;
- MagRez magnet - $ 8;
- Variable resistor - $ 1 ;.
- Buttons for the handle (three boards - switching, front, end) - $ 5 ;.
- Buttons for housing - $ 2.

The second copy of "RUD 4x4" in the case of the "milk" acrylic and proximity sensors (magrezy) on all 4 axes mechanics, controller at 4096 samples per axle.
The price of 200 US dollars.

"White" is sold.
In assembling the throttle to the handle of the Cougar ...

soon

Another left to the owner ...

Today gathered rod handle mounting from Cougar, I liked the result.

GVL224,

How did you connect the potentiometer to the throttle axle?

A plastic/rubber hose acting as joint?

http://forum.il2sturmovik.ru/uploads/monthly_06_2015/post-586-0-77232100-1433507463.jpg

Rubber hose, which is very tightly worn on the axis.

Today has received the case for "Trio".
Here's the first fitting ... (with transparent acrylic protective film has not been removed)

Well done.

For those that find strange a F-16 grip on propeller plane:

http://2.bp.blogspot.com/-Kf6JXUwWzCQ/T-CxMYTm2aI/AAAAAAAAASE/GmVaw3tUTAQ/s1600/throttle.jpg
http://1.bp.blogspot.com/-ML2dNR_F0aU/T-Cxg-5OZCI/AAAAAAAAASM/2PCjH5EYYs0/s1600/cockpit3.jpg
http://rv-nation.blogspot.com.br/2013_01_01_archive.html

Trio

"Quartet"

Mechanics "universal" variable current, as well as chiseled aluminum handles.
Mechanics with reinforced rod for mounting on a pipe!

Mechanics for installation on arms Suncom SFS
one mechanic - $ 18.

Another option, the installation handle customer.

X52

http://simhq.com/forum/ubbthreads.php/topics/4184875/Selling_control_unit_(Throttle#Post4184875

Individual order, under the handle Cougar

Individual order

http://simhq.com/forum/ubbthreads.php/topics/4274617#Post4274617

Individual order.

https://www.youtube.com/watch?v=UwQR0OPLltc

These kits are from 15 to 17 us dollars? That's a great deal! They look terrific, and I need metal for my throttle project. I will definitely be in touch with you about these. Would I be able to get a custom sized/bent lever arm? (for more money of course) I have drawings to go from.

Individual project for three mechanics, one resistor, and 16 buttons.
https://www.youtube.com/watch?v=ZkXG6YZ_D50

If you need a lever of individual form, then send me a drawing, I will try to adapt it to your mechanic.

Calibration of the controller on the throttle
https://www.youtube.com/watch?v=q1Yo00y-UWI

Here the black version!
(Multiple locations arms)
https://www.youtube.com/watch?v=yNfnSJmmriI

Before New Year discount of 15% or mail at my expense.

"RUD 4 * 4" with the new location of the front panel and processed (reduced a little) mechanics.
Price US $ 160 + shipping. If outside Ukraine it is 20 US dollars.

New

Throttle GVL224 "RUD 2x6"

Video
https://youtu.be/OYr67IJOsqk

Video
https://www.youtube.com/watch?v=xsBso_bnSQI

What's inside the block "RUD 4x4"?
https://youtu.be/-fUJrpYzz9E

In the control unit "Sextet" 6 mechanics GVL224 (6 universal) are installed.
Iron mechanics, axles on bearings with non-contact sensors.

Front panel:
- 2 axes on variable resistors (potentiometers);
- 4 buttons;
- 6 toggle switches without locks in the extreme positions (like 12 buttons).

Total we have 8 axes and 34 buttons.

The case is made of acrylic 3mm thick, collected as a 3D puzzle ..., available in black, white and transparent.
https://youtu.be/I4zxhWG0mGA

Trio

"Cyclone", an individual project for the installation of a handle from the X-52
https://youtu.be/MCchQ0U7QW0

Another version of the mechanics of Sparka.

These are two levers in one mechanism, the distance between the levers (rods) is 27.6 mm.

Redesigned model for three positions (microswitch).

More than three microswitches can not be placed, but if you put the MagPes and program it into sectors, then you can do more things.

Nice.

Elegant spring solution.

Another model of the throttle "RUD 3 * 5"
https://www.youtube.com/watch?v=7mhAKEBZsl0

The mechanics of "Sparka" alya "Me109"

Throttle GVL224 "RUD 3х3"
https://youtu.be/GmasHzsR0fo

"Spark" in the metal

Mechanics for three fixed positions of the handle with a pull rod.

The ball is on stock as an arm version.

Spring is also not the final option
.

Video mechanics with fixation
https://youtu.be/_xA-skt8HFw

Another option.

The "screw pitch" handle is printed on a 3D printer

Mechanics with fixation for 5 positions.

The number of positions can be any (how many slots fit on the bar).

The position of the stem is removed by a non-contacting sensor, Mareps.

If the controller or the program allows you to split the entire range into sectors and assign each value to each sector, it is possible to assign a specific action to each position of the stock in the program (simulator).

Handles a 3D printer.

Got mine in and it's awesome. I will give a detailed review later but so far I love the throttle. I've used most of them in the past and this is by far the best.

I'm glad that you liked my throttle.

3D printing

While I will not open a new topic, I will place it in this one.

The control panel.

Used the controller MJoy16. Installed 11 buttons with the ability to highlight, 1 mini-stick, 4 encoders, 1 potentiometer and two toggle switches with protective covers. Inside, there is still room for the installation of a second controller which, according to the customer's plan, will control the backlighting of the buttons. The case material is 1.5 mm steel cut on the laser and bent by a bending machine. Width 31 cm, depth 10 cm, height with legs 6.7 cm.

I forgot my link to the video https://www.youtube.com/watch?v=roVO-fG5xsI

New handles fully printed on a 3D printer.
https://www.youtube.com/watch?v=g_5c0_tFYxE

Handles based on Me109

I can print it completely yellow.

Mechanics "Lefty"

Handle under the right hand.

Mechanics "Crane chassis" A-10
With the backlight of the handle.
The mechanics of mine are "fixed" to two positions, and the handle is the size and style of A-10.
https://www.youtube.com/watch?v=EAt1QUapY1Y



"Base" handles for Fw-190 and handle Fw-190 Bf-109
Installed also on my mechanics "RUD"

New mechanics "Не-111" on the basis of "spark".
The stock is enlarged long, "balls" with a diameter of 35mm.

Throttle block "two in one".
Me109 + He111.
The size of the base is 225mm * 200mm
https://youtu.be/_CkFzrzhWhc

It turned out here is such a handle (Me109) on the main axis of the throttle
https://youtu.be/KtewLVvld48

In the new building.

Material "Aluminum composite panel".

The mechanics are combined, along the edges "universal" in the center of the "spark".

The inscriptions are made with laser engraving.
https://youtu.be/FXGGEekz9YY

Here is another option
https://youtu.be/aNSym7NUJfg

RUD 4x4 with small arms in Yak's style.
https://youtu.be/JFFw0h7SKyo

Ме109

Simplified (cheaper) version of the "RUD 2*6"
https://youtu.be/S2mb_2uaeB8

Very nice

Marc..

Here such variant.

The main difference from the previous is an elongated handle 15 mm from the standard and two "twisters".

One krutilka from below (as I have already done) and from the front (this was the first time I did it).

https://youtu.be/eyIrLpKa5b4

i would like to order one of your throttle units based on your 109 +111 designs BUT due to the space constraints of my sim pit it would have to be the same width as a thrust master wart hog throttle it could however be a bit longer than the warthog, also the side would have to be clean of switches and dials. would love to buy one from you i've liked your work for some time, i will have to send you photos of my set up by email as i have not yet learnt how to post proper photos on this forum would this be acceptable ?

thanks for your time GVL224.

Hello.
Write and send a photo to my e-mail gvl224@ukr.net
So it will be more convenient.

I want to ask your opinion, is such a revision of the main lever will be in demand?

If someone don't understand the purpose of this "red L lever" in the drawing:



The red lever under throttle grip is for bi-pass the the stop/detend near end or throttle course.

This "stop" purpose is simulate the 'gate'* of some WW2 era throttles that need be overcome for engage boost/WEP, similar of some modern jet's the "afterburner" detent.

The mechanism purposed is based on the one used in Mig-21 throttle lever for by-pass the stop before afterburner range, is choose because don't require changes in the other parts of the throttle.



Now with WW2 games using more detailed engine operation, the Emergency Power is controlled by throttle course instead that generic "gamey" WEP key of early IL-2, for example in Bf 109 of IL-2 Bo'X the rated power is up to around ~83% of throttle course, after this is engaged the Emergency Power.

The purposed "stop" is for avoid player engage Emergency Power inadvertently.

* The 'gate' in WW2 era throttles generally require force the throttle lever for left for by-pass a small 'steep'. Example of this 'steep' in Hawker Typhoon throttle.

http://spitfirespares.co.uk/Website%20products%20501/T%20Cover%201%20large.jpg
http://spitfirespares.co.uk/Website%20products%20501/throttle%201%20large.jpg
http://spitfirespares.co.uk/Website%20products%20501/throttle2%20large.jpg

Force throttle lever for left in domestic throttle is not practical, in the "heat of the battle" the virtual pilot probable end tilt the entire throttle.

Sokol1, thank you.

Hi GVL did you get the photos can you make me a throttle? i would like to try the new throttle lock too if possible

On the basis of "RUD Me109".

https://youtu.be/wEOg-qK3-88

https://viuly.io/video/rud-throttle-me-109-3-207309

Hi.
Today I received parts for one copy of the supplement to the mechanics.
Write to me on my mail, I check it more often ...

Individual order.

Here is an ore (Throttle) on an individual order.
https://www.youtube.com/watch?v=nc4K_TnLAtk

Bf 109
https://youtu.be/u-KoPDW6lbM

Bf 109 - He 111
https://youtu.be/5EZ21Kr_pXw

Still, with another front panel.

Throttle "Skoda"
https://youtu.be/dDDr1PI-8kw

"Quartet" with different arms.
https://youtu.be/aYw-o1Dz4v0

Continuation of the development of the RUD on the basis of "Bf109"

Model "Il * 2 Sturmovik"
https://youtu.be/BZvepcez8io

My friend has this throttle, but can't get the axes to calibrate properly. All axes are erratic even during the calibration process.

Disregard, we had an issue with a USB hub. It's fixed now.

Yes, 90% of the problems are due to problems with voltage over the UBS.

"Bf. 109-Z"
https://youtu.be/773iPHvBwFE

A small video review of the mechanics of "GVL"
https://www.youtube.com/watch?v=rWjIopSBdAs&t=6s

New "BF 109 - Arthur"

One of the biggest.
https://www.youtube.com/watch?v=M6F5R7SPXAk&t=32s

Bf109 with an individual front panel and two additional buttons on the handle.

https://viuly.io/video/bf109-585637

In the throttle (throttle) "IMMERSER VR" the main difference is the presence of the fifth mechanics in three fixed positions.

And also the presence of 8 encoders, of which two pairs are coaxial.
https://youtu.be/X5K0yDL2oak

Throttle "Tumu"
https://youtu.be/M4byIrFj0Zw

Is it possible to get the landing gear handle with 3 stages like that on in the MiG 21?

Redi_Yeti

Look this version, with 2 or 3 buttons (3 stops) lever at right:

https://youtu.be/X5K0yDL2oak

Yes https://www.youtube.com/watch?v=_xA-skt8HFw

Throttle GVL under the right hand
https://www.youtube.com/watch?v=dZS66x9RR88&t=15s

Fw190
https://youtu.be/lI1BiE8mm5E

For the right hand, for the basis of "IL * 2 Sturmovik"
https://youtu.be/30ifWUPQeKg

throttle "BF109-5"
https://www.youtube.com/watch?v=994o6eSO6Hc

Made to order in 737 style.
https://youtu.be/LZEJ-y_4Irg

Modular throttle in the style of "IL-2"
https://youtu.be/l1Vrvaq5tR0

Reduced version of "Boeing"
https://www.youtube.com/watch?v=zbBAS6uM05Q
https://www.youtube.com/watch?v=QtXre8CrwxE

Panel "Micro"
https://www.youtube.com/watch?v=8qVCXAyI7mw

Modular kit
https://youtu.be/E33d7sloiM8

RUD-2 min
https://youtu.be/lyPKV5gUxCo

Mechanics "Sparka X52" and "Sparka RUD"

Throttle "SWINE" with "afterburner".
https://www.youtube.com/watch?v=0fY9PZtGaUc

Hi, i would like to buy one set for my suncom SFS !

Thanks

Replied to personal messages

Modular throttle Warbird
https://www.youtube.com/watch?v=jA2jN33jgMk&t=1s

TeufelHunden
https://youtu.be/wzUpwCgyVyk

Another throttle under the right hand.
https://youtu.be/MOPee9zIe_M

Lever "Universal" and "Cougar" in one base (Spark).

Throttle "Eagle"
https://www.youtube.com/watch?v=y7eZDAL8ufQ&t=2s
Panels without enclosures for further installation on the customer's frame.

Разработка

Throttle "RUD 4 - right"
https://youtu.be/N9V9TGtU87A

Hello.
I present to you the new mechanics for the throttle.
The peculiarity is that the movement of the handle is straightforward.
This option has a 150mm stroke.
This indicator can be both reduced and increased using shafts of appropriate length.
The length of the required shafts is "handle stroke" + 100mm.
https://youtu.be/yp7he2QmQrk

Linear (rail) mechanics with electronics.
https://youtu.be/4TyRR9Bh350

Rail mechanics with a rod locking mechanism in any pre-selected travel position.

On one mechanic, you can use several racks of limiters.
https://youtu.be/MTus6iYznKc

Electronics for rail mechanics
https://www.youtube.com/watch?v=YAcX6iVemMo

Throttle "Reptilia"
https://www.youtube.com/watch?v=6X0z7QqUE9E

Two throttle "in mirror image" smile
https://youtu.be/sEs-zHsPcnw

https://www.youtube.com/watch?v=9zgqEbY_8D0

https://youtu.be/I4T4FaDo2g8

Upgraded my pedals at FFB.