#4600597 - 05/30/22 10:59 AM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, PLAN B. Damaged CDL decal, fuselage decals removed. Black squadron stripes airbrushed, fuselage and 'Lift Here' decals replaced. 'Flory Models' Dark Dirt and Grime clay washes applied. Sealed with 'Alclad' Light Sheen (ALC-311) clear lacquer. Hopefully a more dirty, 'war weary' finish. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4600652 - 05/30/22 07:33 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, The kit supplies a photo-etch carrier for three spare ammunition drums for the Lewis machine guns. Various profiles and photographs show these carriers to have storage for different amounts of ammunition drums. The photograph below show a captured No.13 Squadron BE2c with a four drum carrier, as does the colour profile I'm using for this model. Therefore I chose to make this type of carrier from 0.2 mm thick plastic card. This was primed white then airbrushed with 'Tamiya' Dark Yellow (XF60). I then brushed Windsor and Newton Raw Sienna (Griffin Alykld). The four ammunition drums are those from the replacement 'GasPatch' Lewis Mk.1 stripped half heatsinks (32-32052) set. They were airbrushed with 'Tamiya' Gloss Black (X1), then with 'Alclad' Steel (ALC-112). The rounds were brushed painted with 'Mr. Colour' Brass (219) with 'AK Interactive' Brown Leather (AK3031) for the hand straps. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4600721 - 05/31/22 08:04 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, The engine is now fitted, including the upper auxiliary fuel tank and it's tube connecting it to the main fuel tank under the observers seat. The kit supplied top cowl is supplied as either resin or photo-etch, but neither seem curved enough at the top when fitted. Also the RAF 1a engine had baffle plates fitted between the engine cylinders and these are not provided for in the kit. Therefore it looks like I'll need to make the cowl and baffles instead, Mike
Last edited by Sandbagger; 05/31/22 08:06 PM.
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4600722 - 05/31/22 08:17 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, A few more observations of areas of the model not included. Later versions of the BE2c had an access panel on the right side of the fuselage and rear of the pilot’s cockpit. This panel is not included on the kit fuselage and will need to be created. Later versions of the BE2c had either one or two circular access panels on the left side of the nose, on the triangular panel. This panel is not included on the kit. Also most BE2c aircraft had a twin pitot tube fitted to an outboard interplane strut. Also not included in the kit. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4600762 - 06/01/22 12:45 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, The weapons are now finished, although the observers Lewis will be finally positioned on its swivel mounting once the rigging etc is completed. The Lewis machine gun for the observer was mounted on a tubular swivel arm located centrally between the observer and pilots cockpits. The Lewis machine gun for the pilot was mounted to the side of the cockpit and angled to fire obliquely outboard. Both weapons and the spare ammunition drums are the ‘GasPatch’ Lewis Mk.1 stripped half heat sinks (32-32052). The observers weapon has a 0.3 mm diameter rod fitted to allow it to swivel on the gun mounting. Similarly the pilots weapon has a rod fitted to locate it into a hole drilled into the side of the fuselage. I chose not to use the kit supplied photo-etch mounting for the pilots weapon as is was way to flimsy. Both weapons were primed with 'Tamiya' Gloss Black (X1) then airbrushed with 'Alclad' Gun Metal (ALC120). Then ‘Mr. Colour’ Super Metallic - Super Iron (203) was dry brushed over the weapons. Finally 'Tamiya' Hull Red (XF9) was applied to the handles and 'AK Interactive' Brown Leather (AK3031) to the drum straps. A light wash os 'AK Interactive' Kerosene (AK2039) was applied over the ammunition drums. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4601173 - 06/06/22 05:50 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, On most BE2c aircraft, linen was wrapped around the four fuselage cabane struts and the landing gear struts. This was done to protect the struts and to help prevent the wood from splitting. To represent the linen wrapping I used cut thin strips of plumbers Polytetrafluoroethylene (PTFE) tape. This tape is by nature very thin and will self-grip to tools and your fingers, so patience and repeated cutting will be necessary. The tape was secured in position using thin CA adhesive. Then airbrushed with 'Alclad' Light Sheen (ALC311), treated with 'Flory Models' Grime wash and finally clear coated again. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4601445 - 06/09/22 06:58 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, Well, the most difficult part of this model build, the top engine cowl, is done. Without going into detail (as it's covered in my build log), I had to effectively scratch the cowl. The kit supplied photo-etch or resin cowls were discarded. I used the centre section of the photo-etch panel, annealed and bent into shape. The retaining straps from the cowl onto the cylinder head bolts, the cylinder baffles and the fire wall were made from 0.2 mm thick plastic card. The centre support strut under the cowl and into the engine block is painted 0.4 mm diameter tube. Now it's onto pre-rigging, Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4601644 - 06/13/22 08:02 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, Just a few updates. The bomb racks, wheels, interplane struts and propeller. I'm now finishing off the eight 'Hale' heavy case Mk.II/C bombs, Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4601698 - 06/14/22 12:48 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, A couple more updates. The photo-etch camera mounting, which represents the CFS Mk.II/C mounting. Also the three fuselage windows are done. The photo-etch frames for the two square side windows were secured in position over the created openings, using thin CA adhesive. I then infilled the frames with 'Microscale' Krystal Kleer, which once cured leaves a transparent film. The opening in the larger rectangular window is too large to apply Krystal Kleer straight off. Therefore I cut a very thin strip from the supplied windscreen acetate sheet. The strip was just long enough to span across the centre, underside of the photo-etch frame. This effectively creates two smaller openings for applying the Krystal Kleer. The frame was then added to the fuselage in the same manner used for the side windows, Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4601735 - 06/14/22 06:43 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, The eight 'Hale' 20lb heavy case MkII/C bombs. The red and green stripes were decals taken from another model kit. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4601811 - 06/15/22 04:47 PM
Re: 1:32nd scale RAF BE2c
[Re: Sandbagger]
|
Joined: May 2016
Posts: 1,523
BuckeyeBob
Member
|
Member
Joined: May 2016
Posts: 1,523
Ohio, USA
|
I agree, catch.
"Out of crisis comes opportunity."
Great job, Mike.
“With Major Lawrence, mercy is a passion. With me it is merely good manners. You may judge which motive is the more reliable.”
|
|
|
|
|
|
|
|
|
|
Exodus
by RedOneAlpha. 04/18/24 05:46 PM
|
|
|
|
|
|