Previous Thread
Next Thread
Print Thread
Rate This Thread
Hop To
Page 2 of 5 1 2 3 4 5
#4523989 - 06/05/20 06:38 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
I've separated the resin elevator from the tail plane and added 0.4 mm rods, to enable the elevator to be animated.
The pilot's and ground crew grab handles were drilled out, reshaped then 0.85 mm styrene rectangular rod added to correct the open shape and correctly locate the handles (which were actually a fuselage longeron).
The forward decking panel was hinged at both sides by continuous hinges located under the cooling jackets for the two machine guns.
These are not moulded on the kit part so have been represented by using 'Aviattic' photo-etch rib tapes.

Mike

[Linked Image]

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4524087 - 06/06/20 12:57 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
The upper wing, as supplied in the basic kit, has a pronounced bow across the thicker, centre section of the wing.
As the underside of the wing in that area has a glossy finish, I can only assume the bow was caused during the injection process.
Unlike resin parts, polystyrene seems to retain a shape 'memory' once moulded, so it can be more difficult to correct distortions without introducing white 'stress' marks in the part.
However I applied heat on both sides of the wing centre section from a hair dryer (on high setting).
The heat was maintained for a few minutes Then the wing was flexed and held in position whilst cooling.

Mike

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4524091 - 06/06/20 01:23 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Nov 2014
Posts: 3,696
Fullofit Offline
Senior Member
Fullofit  Offline
Senior Member

Joined: Nov 2014
Posts: 3,696
Ajax, ON
Did you remember to quench after annealing? smash


"Take the cylinder out of my kidneys,
The connecting rod out of my brain, my brain,
From out of my arse take the camshaft,
And assemble the engine again."
#4524154 - 06/06/20 10:34 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
Earlier Siemens-Schuckert aircraft designs were basically copied from French Nieuport fighters, such as the Nieuport 11.
The method of aileron control used for the Siemens-Schuckert D.III was not the usual cable systems, but was a copy of the French design using control rods from the cockpit to the upper wing.
The pilot’s control column was attached to a torque bar, which was located across the cockpit floor.
The ends of this tube were attached by universal joints to control rods, which were routed up and out of the cockpit forward decking.
The control rods attached to bell crank levers in the upper wing and control rods from these routed outboard to the ailerons.

[Linked Image]

The cockpit to upper wing control rods/bell cranks are represented in the kit, but only to the underside of the upper wing.
Photographs of the aircraft show what appears to be cut outs, which allows the tops of the aileron bell cranks to protrude slightly through the top surface of the upper wing.
These cut outs are represented on the kit wing as recesses on the underside and raised solid moulded rectangles on the top surface.
Also the kit control rod/bell crank part have round rods, whereas the actual rods were flat sided (streamlined).

I drilled out the aileron apertures in the upper wing then scrapped them to the required shape.
The kit aileron control rod/bell cranks were reduced in thickness to more represent the actual parts.
Small squares of 0.85 mm thick plastic card was cemented onto the bell cranks and were then rounded and drilled with a 0.5 mm diameter drill.
Short lengths of 0.5 mm Nickel-Silver tube were cut and secured through the pre-drilled holes.
The modified parts are a snug fit into the wing apertures and will be fitted later in the build,

Mike

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4524625 - 06/09/20 01:09 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
The aircraft had padding protection for the pilot in three areas:
Padding at the front of the cockpit decking.
Padded headrest on the front of the fuselage fairing.
Padding around the centre section cut out in the trailing edge of the upper wing.
The padding on the headrest is moulded on the fairing but is slightly offset and hardly visible. The padding on the upper wing is not represented in the kit.
I added both by using 'Milliput' two part putty.

[Linked Image]

[Linked Image]

The ‘Brengun’ Siemens Schuckert D.III (BRL32014) photo-etch set has the parts to create a pilot’s seat.
However I chose not to use those parts as photo-etch parts are in some cases too thin to be realistic. The pilot’s seat is such as case.
Therefore I used the photo-etch seat back as a guide to drill out the kit supplied seat, then added a seat cushion made from 'Milliput', as the kit does not supply a cushion.

[Linked Image]

That's the last modifications at this preparation stage, so now I can start the actual building phase.

Mike


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4524654 - 06/09/20 03:46 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Jun 2012
Posts: 7,993
Robert_Wiggins Offline
BWOC Survivor!...So Far!!
Robert_Wiggins  Offline
BWOC Survivor!...So Far!!
Hotshot

Joined: Jun 2012
Posts: 7,993
Lindsay, Ontario, Canada
It's coming along nicely Mike!


(System_Specs)
Case: Cooler Master Storm Trooper
PSU: Ultra X3,1000-Watt
MB: Asus Maximus VI Extreme
Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered
CPU: Intel i7-4770K, OC to 4.427Ghz
CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler
Vid Card: ASUS GTX 980Ti STRIX 6GB
OS and Games on separate: Samsung 840 Series 250GB SSD
Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L
Periphs: MS Sidewinder FFB2 Pro, TrackIR 4

#4524823 - 06/10/20 04:55 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
The top decking panel has its photo-etch panels fitted (the quarter turn fasteners will be fitted later).
I'd previously fitted photo-etch hinges to the panel, however the 'Brengun' photo-etch panels include these hinges.
Also the tail skid support brackets are fitted.

[Linked Image]

[Linked Image]

Well, I thought I'd covered all the necessary changes before starting the build.
However I've found other changes that need to be done.

The right fuselage half from the kit has a scooped vent, which was not fitted to the early D.III, so that was removed and filled.

[Linked Image]

[Linked Image]

That allowed me to fit the two photo-etch side access panels, which again are different in desin from those fitted to the later D.III.

[Linked Image]

The kit fuselage halves are missing a panel join at fuselage former E - this needs to be scribbed onto the fuselage halves.

[Linked Image]

[Linked Image]

The underside vented panel is different from the later D.III, which had two scooped vents fitted. The early D.II had no vents, but an access panel was fitted.
This means the photo-etch panel supplied with the 'Brengun' set is not correct for this model, so I'll probably modify the kit panel.

[Linked Image]

[Linked Image]

The left fuselage half from the kit has a poorly moulded pilot's foot step, which in reality was a retractable to close off when not in use.
The kit location for the foot step is incorrect as it's too high above the lower wing root. I'll fill this foot step and create a new one.

[Linked Image]

[Linked Image]

Apart from that it's plain sailing so far!!!

Mike


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4525010 - 06/11/20 05:20 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
I've used the kit under panel and opened up the louvre vents and added the panels retaining screw and louvre rivet locations.
Also filled the original pilot's foot step and created a new one in the correct position.
Finally added the missing panel line at the fuselage former.

Mike

[Linked Image]

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4525011 - 06/11/20 05:23 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: May 2016
Posts: 1,523
BuckeyeBob Offline
Member
BuckeyeBob  Offline
Member

Joined: May 2016
Posts: 1,523
Ohio, USA
Cool! One of my favorite planes, so really looking forward to this one!


“With Major Lawrence, mercy is a passion. With me it is merely good manners. You may judge which motive is the more reliable.”
#4525461 - 06/14/20 04:41 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
A few updates for the build.

When I temporarily joined the fuselage halves I found the seat support frame was too short and didn't reach its locations in the fuselage sides.
To correct this I cut the frame cross members and added 1.4 mm diameter tubes to extend the width of the frame.

[Linked Image]

The 'Brengun' photo-etch side formers and box cover were added - tricky to fit under the cockpit side 'Z' frames and required thinning the frame and filing the photo-etch.

[Linked Image]

The 'Brengun' set has a side panel, the location of which is not clear in the instructions.
However a photo shows where it locates.

[Linked Image]

[Linked Image]

The front decking panel and the replacement 'Gaspatch' machine guns were modified to allow the guns to fit the panel.
The kit supplied ammunition feed and ejection chutes were used and pinned through the gun breech block with 0.5 mm diameter rod.

[Linked Image]

Mike


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4525465 - 06/14/20 04:49 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2012
Posts: 3,086
MFair Offline
Senior Member
MFair  Offline
Senior Member

Joined: Dec 2012
Posts: 3,086
No detail to small Mike. This is going to be one of best yet me thinks!


Never approach a bull from the front, a horse from the rear or a fool from either end.
BOC Member since....I can't remember!
#4525635 - 06/15/20 06:38 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
I did some research to ascertain the purpose of the rectangular access panel under the early D.III aircraft.

[Linked Image]

It seems that the loaded belts of ammunition for both machine guns were stored in the ammunition container fitted under both guns.
The loaded ammunition belts were fed to the gun breech blocks through feed chutes.
The empty ammunition belts were directed from the breech blocks through chutes to box containers, which were fitted to the fuselage sides inside the cockpit.

All of the empty ammunition cases from both weapons were ejected through a tube connected to the lower front of each breech block and from there into a combined ejection pipe which was routed down to the bottom of the fuselage.
On the later D.IV aircraft the cases were discharged out of the aircraft from the ejection pipe opening under the fuselage.
However, in the early D.III aircraft the cases were retained in a container inside the fuselage and to access the container for emptying, the rectangular access panel was fitted under the fuselage.

[Linked Image]

Mike


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4525640 - 06/15/20 07:13 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Jun 2012
Posts: 7,993
Robert_Wiggins Offline
BWOC Survivor!...So Far!!
Robert_Wiggins  Offline
BWOC Survivor!...So Far!!
Hotshot

Joined: Jun 2012
Posts: 7,993
Lindsay, Ontario, Canada
Hi Mike;

I just noticed the spent cartridge chute inside the cockpit. Geez, I would hate to have all those spent cartridges rolling around and getting under various control levers and cables, not to mention having them all rush up and hit me in the face when I did a roll!!

I sure hope they were ejected outside the cockpit!!

He He!!

Last edited by Robert_Wiggins; 06/15/20 07:13 PM.

(System_Specs)
Case: Cooler Master Storm Trooper
PSU: Ultra X3,1000-Watt
MB: Asus Maximus VI Extreme
Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered
CPU: Intel i7-4770K, OC to 4.427Ghz
CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler
Vid Card: ASUS GTX 980Ti STRIX 6GB
OS and Games on separate: Samsung 840 Series 250GB SSD
Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L
Periphs: MS Sidewinder FFB2 Pro, TrackIR 4

#4525796 - 06/16/20 06:58 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Robert_Wiggins]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi Rob,
The early D.III stored the spent cartridges in a container in the bottom of the fuselage.
The panel under the fuselage was used to access the container to remove the cartridges.
The later D.IV didn't retain the spent cartridges and instead just dumped them out through the open ejector pipe under the fuselage,

Mike.


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4525798 - 06/16/20 07:09 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
Cross bracing wires were fitted between the tops of the rear fuselage cabane struts and the inside of the fuselage.
These wires were attached to a small rectangular frame, located on the top centre of the cockpit front decking panel.
Each of the four separate bracing wires were attached the corners of this frame.

[Linked Image]

The model has the rectangular attachment frame moulded solid, which does not represent the actual frame.
The ‘Brengun’ photo-etch set has two frames, either of which (or both) can be used, but attaching them to the decking panel and rigging is not explained.

I removed the pre-moulded lump and drilled two holes of 0.5 mm diameter at approximately 60 degrees, down and through the front decking panel.
Two lines of 0.08 mm diameter mono-filament were passed through 0.4 mm diameter tube, then through the photo-etch frame.
The lines were looped back through the tubes the secured in position with thin CA adhesive.
The following shot shows it test fitted. The frame will be finally fitted later in the build during the rigging phase,

Mike

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4525943 - 06/17/20 02:18 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
I really should build models out of the box (OOB).
I followed the instructions for embodying the ‘Loon Models’ resin wing tips for the early version aircraft.
Now I've found that the span of the lower wing is 12 mm too short (6 mm at each wing tip).
As can be seen, when the modified wings are laid onto a correctly resized drawing, the span of the upper wing is correct, but the span of the lower wing is not.
The original kit is for the later D.IV aircraft, the lower wing of which had a slightly shorter span when compared to the upper wing (disregarding the extended balanced ailerons).
So now, having embodied the modifications to both wings, I'm not sure whether the 'Loon Models' instructions for cutting away the kit wing tips are incorrect or the wing span of the original kit supplied lower wing is too short?

[Linked Image]

[Linked Image]

[Linked Image]

Anyway, I'll need to cut the lower wing at both sides and along a rib line then pin and pack the wings to the correct span.
This will also mean relocating the lower wing location holes for the outer wing struts.

Mike


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4525997 - 06/17/20 08:14 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Jun 2012
Posts: 7,993
Robert_Wiggins Offline
BWOC Survivor!...So Far!!
Robert_Wiggins  Offline
BWOC Survivor!...So Far!!
Hotshot

Joined: Jun 2012
Posts: 7,993
Lindsay, Ontario, Canada
Geez.....


(System_Specs)
Case: Cooler Master Storm Trooper
PSU: Ultra X3,1000-Watt
MB: Asus Maximus VI Extreme
Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered
CPU: Intel i7-4770K, OC to 4.427Ghz
CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler
Vid Card: ASUS GTX 980Ti STRIX 6GB
OS and Games on separate: Samsung 840 Series 250GB SSD
Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L
Periphs: MS Sidewinder FFB2 Pro, TrackIR 4

#4526213 - 06/18/20 07:37 PM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2000
Posts: 7,060
Sandbagger Offline
Hotshot
Sandbagger  Offline
Hotshot

Joined: Dec 2000
Posts: 7,060
Coningsby, Lincs, UK
Hi all,
To correct the span of the lower wing:
Wing cut through 30 mm from the wing roots.
Two holes drilled (0.5 mm diameter) into outer wing sections.
Rods (0.5 mm diameter) inserted into holes.
Wings pushed together to indent rods into wing centre section (marks for drilling).
Two holes drilled (0.5 mm diameter) into centre wing section.
Two packs of 6 x 1 mm plastic card cemented together.
Two holes drilled through packs to match rods in the wings.
Packs fitted onto wing rods.
Wing sections and packs aligned then secured together with CA adhesive and liquid cement.
Packs filed and sanded to match the wing profiles.
Wing strut location holes filled and re-drilled 6 mm further inboard.

Mike

[Linked Image]

[Linked Image]


[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro
#4526418 - 06/20/20 05:33 AM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Jan 2001
Posts: 1,969
Hentzau Offline
Member
Hentzau  Offline
Member

Joined: Jan 2001
Posts: 1,969
Tampa, Florida USA
Originally Posted by Sandbagger

Wing strut location holes filled and re-drilled 6 mm further inboard.

Mike


First let me say that I love following these builds, some really amazing work. I stop by each day to see what's new. Looking at the above photograph of the actual plane in regard to the model's ailerons it almost looks like the strut should have been moved 6mm outward on the upper wing instead of inward on the lower wing? Regards!

Last edited by Hentzau; 06/20/20 05:37 AM.
#4526434 - 06/20/20 11:02 AM Re: Siemens-Schuckert D.III - 1:32nd scale [Re: Sandbagger]  
Joined: Dec 2012
Posts: 3,086
MFair Offline
Senior Member
MFair  Offline
Senior Member

Joined: Dec 2012
Posts: 3,086
“I really should build models out of the box (OOB).“

Mike,
If you ever did, I think you would through it out with yesterday’s laundry. thumbsup


Never approach a bull from the front, a horse from the rear or a fool from either end.
BOC Member since....I can't remember!
Page 2 of 5 1 2 3 4 5

Moderated by  Polovski 

Quick Search
Recent Articles
Support SimHQ

If you shop on Amazon use this Amazon link to support SimHQ
.
Social


Recent Topics
Carnival Cruise Ship Fire....... Again
by F4UDash4. 03/26/24 05:58 PM
Baltimore Bridge Collapse
by F4UDash4. 03/26/24 05:51 PM
The Oldest WWII Veterans
by F4UDash4. 03/24/24 09:21 PM
They got fired after this.
by Wigean. 03/20/24 08:19 PM
Grown ups joke time
by NoFlyBoy. 03/18/24 10:34 PM
Anyone Heard from Nimits?
by F4UDash4. 03/18/24 10:01 PM
RIP Gemini/Apollo astronaut Tom Stafford
by semmern. 03/18/24 02:14 PM
10 years after 3/8/2014
by NoFlyBoy. 03/17/24 10:25 AM
Powered by UBB.threads™ PHP Forum Software 7.6.0