#4501751 - 12/27/19 06:56 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, I've now added all of the necessary photo-etch parts to the fuselage and lower wing halves. Also the main undercarriage, a windscreen (which wasn't supplied in the kit) and a flare pistol and cartridge rack (not supplied in the kit, but often carried on this aircraft). The whole lot has been sealed with a semi-matte lacquer, ready for a 'Flory Models' clay weathering wash. I've still got to add a small pipe to the radiator condenser assembly and two cross bracing cable at the rear of the engine bay. These will be attached to the underside of the upper wing centre section. Also the propeller shaft access hole. Then it's onto pre-rigging and fitting the wings Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4501810 - 12/28/19 06:52 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, Just a few minor additions. The upper wing was cross braced from the top of the rear cabane struts to the bottom of the opposite rear cabane struts. These are not detailed in the kit. I've drilled holes for adding the cross bracing through the cockpit front decking later in the build. The 'ProperPlane' Knoller-Jaray propeller has a 2.0 mm diameter tube added for mounting into the fuselage. The small pipe on the top of the radiator condenser assembly has also been added, using 0.4 mm diameter Nickel-Silver tube. Now it's onto weathering with clay wash, pre-rigging the wings and fitting them, which I know already will give me problems with alignment!! Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4501846 - 12/29/19 11:07 AM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Thanks James - I try Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4501887 - 12/29/19 09:39 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Jun 2012
Posts: 7,993
Robert_Wiggins
BWOC Survivor!...So Far!!
|
BWOC Survivor!...So Far!!
Hotshot
Joined: Jun 2012
Posts: 7,993
Lindsay, Ontario, Canada
|
Mike that is turning into a fine model worhy of note!
Was that condenser pipe an after market or scratch built? It is very close to the photo in accuracy.
Best Regards
Case: Cooler Master Storm Trooper PSU: Ultra X3,1000-Watt MB: Asus Maximus VI Extreme Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered CPU: Intel i7-4770K, OC to 4.427Ghz CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler Vid Card: ASUS GTX 980Ti STRIX 6GB OS and Games on separate: Samsung 840 Series 250GB SSD Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L Periphs: MS Sidewinder FFB2 Pro, TrackIR 4
|
|
|
#4501919 - 12/30/19 11:39 AM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi Rob, No, just a 0.4 mm Nickel-Silver tube bent to 90 degrees and set in the condenser - nothing fancy really,
Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4501969 - 12/30/19 06:01 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Jun 2012
Posts: 7,993
Robert_Wiggins
BWOC Survivor!...So Far!!
|
BWOC Survivor!...So Far!!
Hotshot
Joined: Jun 2012
Posts: 7,993
Lindsay, Ontario, Canada
|
Steve, you are a persistent enthusiast! As they say, nothing ventured, nothing gained! I'll start the bidding with 5 Marks!!
Case: Cooler Master Storm Trooper PSU: Ultra X3,1000-Watt MB: Asus Maximus VI Extreme Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered CPU: Intel i7-4770K, OC to 4.427Ghz CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler Vid Card: ASUS GTX 980Ti STRIX 6GB OS and Games on separate: Samsung 840 Series 250GB SSD Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L Periphs: MS Sidewinder FFB2 Pro, TrackIR 4
|
|
|
#4501970 - 12/30/19 06:04 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: May 2012
Posts: 4,879
RAF_Louvert
BOC President; Pilot Extraordinaire; Humble Man
|
BOC President; Pilot Extraordinaire; Humble Man
Senior Member
Joined: May 2012
Posts: 4,879
L'Etoile du Nord
|
|
|
|
#4501983 - 12/30/19 07:33 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Heh he - as Rob knows it would take a little more then that just to cover shipping insurance Hi all, I've applied the 'Flory Models' Dark Dirt clay wash to give a 'subtle' grimy look - I added a few drops of washing up liquid to break the surface tension of the wash to help it spread more over the model. The wash wash applied by brush. Once the required amount was wiped away with a very slightly damp tissue and brush, I sealed it all with 'Alclad' Semi-Matte (ALC-312) lacquer. I've also prepared the rigging and control lines. The next step is to install the pre-rigged lines and fit the wings, so as to be able to complete the rigging. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4502053 - 12/31/19 01:56 AM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, The tail unit is now rigged with cross bracing cables and rudder and elevator control lines. A combination of 0.12 mm and 0.08 mm mono-filament with either 0.4 mm or 0.5 mm diameter Nickel-Silver tube and 'Gaspatch' metal 1:48th scale turnbuckles (Types A and C). Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4502102 - 12/31/19 03:14 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Jun 2012
Posts: 7,993
Robert_Wiggins
BWOC Survivor!...So Far!!
|
BWOC Survivor!...So Far!!
Hotshot
Joined: Jun 2012
Posts: 7,993
Lindsay, Ontario, Canada
|
Heh he - as Rob knows it would take a little more then that just to cover shipping insurance How true, how true!! Good one Mike! When do you plan to take a break!! You're as committed as OBD staff!!
Case: Cooler Master Storm Trooper PSU: Ultra X3,1000-Watt MB: Asus Maximus VI Extreme Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered CPU: Intel i7-4770K, OC to 4.427Ghz CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler Vid Card: ASUS GTX 980Ti STRIX 6GB OS and Games on separate: Samsung 840 Series 250GB SSD Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L Periphs: MS Sidewinder FFB2 Pro, TrackIR 4
|
|
|
#4502548 - 01/03/20 03:50 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, I spotted that the upper surfaces of the lower wings, at the forward wing root area, had protective ‘walkways’ fitted, presumably to protect the wing surfaces from being damaged whilst the engine area was being worked on by ground crew (too far forward for pilot’s access). As no details of this could be found, I’ve assumed this was possibly reinforced plywood fitted under the lozenge linen wing covering or a thin metal design and fitted over the lozenge linen covering of the wings. I decided, more for aesthetics, that I'd use metal mesh from 'RB Productions', which was cut to share and secured in position using thin CA adhesive. They were then weathered using 'Flory Models' Dark Dirt and Grime clay washes and then dusted with pigments. Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4502555 - 01/03/20 04:29 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Jun 2012
Posts: 7,993
Robert_Wiggins
BWOC Survivor!...So Far!!
|
BWOC Survivor!...So Far!!
Hotshot
Joined: Jun 2012
Posts: 7,993
Lindsay, Ontario, Canada
|
Mike that is interesting about the walkway. It's not very clear in the photo but might be easier to see if the photo is w as lightened. Do you think this might have been a field fix?
Case: Cooler Master Storm Trooper PSU: Ultra X3,1000-Watt MB: Asus Maximus VI Extreme Mem: Corsair Vengeance (2x 8GB), PC3-12800, DDR3-1600MHz, Unbuffered CPU: Intel i7-4770K, OC to 4.427Ghz CPU Cooler: Cooler Master Seidon 240M Liquid CPU Cooler Vid Card: ASUS GTX 980Ti STRIX 6GB OS and Games on separate: Samsung 840 Series 250GB SSD Monitor: Primary ASUS PG27AQ 4k; Secondary Samsung SyncMaster BX2450L Periphs: MS Sidewinder FFB2 Pro, TrackIR 4
|
|
|
#4502559 - 01/03/20 04:55 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi Rob, Yes I tried that but it's not much clearer. Looking at all of the photographs I could find it seems most 'Bergs' had these fitted, so I suspect it would have been a factory installation, rather than an 'in-service field mod', Anyway the lower wings are fitted now. Given the wings are pinned into the fuselage at the trailing edge, but only supported at the leading edge by the front spar bracing bar 'resting' on the underside of the fuselage, it leaves the wings liable (with handling) to break free at the front and pivot down on the rear support pins. There didn't appear to be any additional bracing bar support fitted to the actual aircraft, so with 'poetic license' I've added 'U' tube supports over the bar (at the outer ends) and secured them into the fuselage underside. They should provide extra support for the wings and prevent 'break away' until the upper wing is finally fitted, Mike
Last edited by Sandbagger; 01/03/20 08:59 PM.
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4502647 - 01/04/20 05:41 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, The upper wing underside has been pre-rigged, ready for fitting, Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4502649 - 01/04/20 07:28 PM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: Dec 2000
Posts: 7,064
Sandbagger
Hotshot
|
Hotshot
Joined: Dec 2000
Posts: 7,064
Coningsby, Lincs, UK
|
Hi all, Undercarriage cross bracing wires fitted, Mike
Alienware Aurora R5 Windows 10 64 bit Intel i7-6700K 4.2Ghz Two GTX 1080 Foundations in SLI (8 Gig each) 32 Gig DDR4 2133Mhz 1TB SSD boot drive - 1TB SATA storage drive 5.1 Surround Sound 34" Dell Ultra Sharp U3415W (3440x 2440) CH Pro-Pedals, Stick and Throttle TrackIR-5 Pro
|
|
|
#4502677 - 01/05/20 02:26 AM
Re: Aviatik 'Berg' D.I
[Re: Sandbagger]
|
Joined: May 2012
Posts: 997
HumanDrone
Just shoot me...
|
Just shoot me...
Member
Joined: May 2012
Posts: 997
Near Pittsburgh, PA USA
|
I'll live long ages before I ever understand how one could develop such a skill set. The details, the weathering, the rigging... dear glory, it's without peer. And the dear chap's retired, which means, come hellfire or high water, presbyopia has set in, and he's working with rigging wires that are about one step up from human hair!
Mike , you are the man. if I ever get meeself retired here, I might actually have time to get a couple of fuselage halves together!
Box: Win7 Pro 64 bit / I72600K @4.1 GHz / EVGA GTX1080Ti/ 16GB RAM / Corsair 240 GB SSD / WD 600 GB Velociraptor / 1050W Power FS Stuff: Saitek X52 Pro Stick/Throttle & Combat Rudder Pedals, TrackIR 5 Sims: FSX Gold, REX 2.0 OD, UTX-NA, FSGenesis 10m mesh/ CFS3 ETO 1.40/Wings Over Flanders Fields BH&H2 (more gorgeous than ever!) Proud BOC inductee 4/30/12!
|
|
|
|
CD WOFF
by Britisheh. 03/28/24 08:05 PM
|
|
|
|
|
|
|
|
|
|
|
|