Hi Crawling_Chaos,
Did you choose it like kit or every parts you had to order independently?
Thanks

Mega_mozg how much memory is available for mmjoy2 firmware? What is maximum that can be flashed?

Great idea! I was thinking about using a Patola box.

Best regards
Crawling Chaos

Hi erichos

I had to purchase the parts according the project I made. They do not offer this set as a kit, since ServoCity is a webstore of robotics components.

Best regards
Crawling Chaos

Are these shift registers from sparkfun with PCB breakouts plug and play?

https://www.sparkfun.com/products/11733

Could I daisy chain several of them together?

http://www.atmel.com/devices/atmega32u4.aspx
Non-volatile Program and Data Memories
– 32KB of In-System Self-Programmable Flash
– 1KB Internal EEPROM

Hello guys ... does anybody know what happened with user Troll and all his posts, his thread or replies? It seems to me that forums no longer knows such user and searches found his thread, but after clicking it displays some error.

please wait, Im trying to talk with him by Skype.

OK, thanks. It's not urgent. I am just curious, because I followed hist thread about ConTroll.

"ConTroller" based on MMJoy2 so you can ask any questions here.

I know I can, but I am still curious what happened ;-). But if it is a secret... I was curious about his further changes in ConTroll and future use of some Hammond box I do plan to use too.

[9:03:27] TROLL @ Jörgen Toll: If you want to post something, just say I left. And give my email to anybody who asks, in a personal message

Ah I see. Thanks a lot for help. I will write him an e-mail. It's a pitty that when someone leave, his posts disappear. This makes confusion in the thread.

@Sokol1

thanks again

Anyone have experience with this PCB hooked into mmjoy2?

This is my OSH park profile

https://oshpark.com/profiles/Debolestis

There are 4 shift register PCBs on that link. You have to solder them, all parts can be found on ebay. They work and can be daisy chained.

Shift from sparkfun will not work. It looks like breakout board.

I'm trying to finish off my pedals but I have run into a road block. The TLE 5011 ICs I purchased don't seem to work. You can see at https://forums.eagle.ru/showthread.php?t=176401 if you are interested.

This is what I have done so far:
I flashed a Pro Micro and tested it with A1302 hall sensors as I am planning on using them for my toe brakes. The A1302 IC's have worked great so far. I then went and copied a PCB for the TLE 5011 sensor I found in an earlier post in this thread. I redesigned it so the sensor sits directly over the centre of axis where the magnet will be placed. Here is the PCB I made:
TLE 5011-3 by John Wall, on Flickr
TLE 5011-4 by John Wall, on Flickr

and this is what it will sit on:

IMG_0872 by John Wall, on Flickr


To continue, I soldered up the TLE 5011 including the resistors and caps to the PCB I made as you saw above. I started the configurator and flashed the board using B2 for the axis and set it to 12 bit precision. Then I tested it. I used the VKB joystick tester but there was nothing to indicating the sensor was being affected by the magnet. It was flatlined. Since I purchased 5 TLE5011's, I tried several more but not one worked. So I went to the protoboard and rebuilt the circuit and tried again with this simple PCB (see below) that I had left over from the RS485 bus I was building. This time I didn't use any resistors or caps. I just wanted to get some kind of signal to verify it worked.
TLE 5011 1 by John Wall, on Flickr


However it was the same as before... Nada! The A1302's are working just fine but the TLE5011 seem dead.

This is what I used for my pinouts:

TLE5010/5011---------->Controller ProMicro(AtMega32u4)
1) 4Mhz clock----------->Pin B6 - Generator 4Mhz
2) SPI-SCK------------->Pin B1 - SPI-SCK
3) SPI-CS--------------->Any free pin
4) SPI-Data------------->Pin B3 - SPI-MISO
5) TST1----------------->To Ground
6) VDD------------------>To Power (VCC)
7) GND------------------>To Ground
8) TST2----------------->To Ground

I read most of the MMJOY2 thread on the SimHQ forum so I was pretty confident I did everything correctly.

Any ideas what might be causing this.

WarHog, check PM (to many quests, Im dont want to distend forum)

Mega_MOZG

Post a updated PCB layout for TLE, will avoid use of early designs. ("Herd effect", like A1302).

How do I get the configurator to run in English? I can't figure it out.