Hi all,
I thought this time around I'd have a crack at building a 1:32 scale model of the Sopwith 'Swallow' monoplane prototype of 1918.

In June 1918, the Sopwith Aviation Company designed an unarmed parasol monoplane, based on the Sopwith ‘Camel’. The aircraft was known the Sopwith Monoplane No.1, but was also known as the Sopwith ‘Scooter’ (to scoot was to move around fast). The aircraft was built for the personal use of the ‘Sopwith’ test pilot Harry Hawker and was based on the their current Sopwith ‘Camel’, but with a single wing mounted just above the fuselage, but with limited space between the fuselage and the underside of the wing. The wing was not supported by the then conventional struts and instead was braced by RAF streamlined bracing wires, all of which were attached to the lower fuselage and a pyramid shaped strut assembly above the wing. The ‘Scooter’ was powered by a single 130 hp (97 kW) ‘Clerget’ 9B rotary engine. The ‘Scooter’ was used as a runabout and aerobatic aircraft by Harry Hawker and was able to demonstrate excellent maneuverability. Eventually it was used as the basis for a fighter design, originally known as the Monoplane No.2, and later named the Sopwith ‘Swallow’.
Like the ‘Scooter’, the ‘Swallow’ used the fuselage of a ‘Camel’, but it had a larger, slightly swept wing of greater wingspan and area. Like the ‘Scooter’ the wing was mounted above the fuselage, but higher, to allow the pilot to access the two synchronized Vickers machine guns, which were fitted further apart than normal, again to give the pilot better forward visibility. For the same reason the ‘hump’ in the forward cockpit decking (hence the name ‘Camel’) was not used. The engine was also changed to that of a 110 hp (82 kW) ‘Le Rhône’ engine. Also the traditional oval shaped access panels on each side of the forward fuselage were omitted. Twelve strengthening ribs were fitted across the centre section on the upper surface of the wing. 
The ‘Swallow’ made its maiden flight in October 1918, and was delivered to RAF Martlesham Heath on 28 October 1918 for official testing. One considered role for the ‘Swallow’ was as a shipboard fighter. Engine problems delayed testing of the ‘Swallow’, but even when the engine problems were resolved, the ‘Swallow’ proved to have a lower overall performance than the then ‘Le Rhône’ engine powered ‘Sopwith’ ‘Camel’. Testing of the ‘Swallow’ continued after the cessation of hostilities but by May 1919 all interest in the ‘Swallow’ was dropped. The fate of the ‘Swallow’ is not known, but presumably it was scrapped.
However the original ‘Scooter’ remained in use, and was given the civil registration K-135 and later to G-EACZ. In 1921, Harry Hawker purchased and flew the ‘Scooter’. Harry Hawker died on the 12th July 1921 in a flying accident at Hendon, after which the ‘Scooter’ was put into storage. It was refurbished in 1925 and was used for aerobatic displays and for racing until 1927 when it was scrapped.

Some time back I purchased the only 1:32 scale conversion set available, which is a resin set intended for the Hobby Craft/Academy Sopwith Camel F.1 kit.
However, that model kit left a lot to be desired, as does the resin set.
Therefore I'm going to try converting the 'Wingnut Wings' 'Clerget' Camel kit.

It may be just the resin conversion set I received, but it has many problems. The wing halves are warped, the front cockpit decking (according to the instructions) is 7 mm too short in length, the upper support wing struts are not tb used, only as guides for making your own, and there's more flash and surface 'blow holes' the I care to mention.

Anyway it'll be another challenge I guess.

Here's a few shots to start off with,

Mike

[Linked Image] 

[Linked Image] 

[Linked Image] 

[Linked Image] 

[Linked Image] 

[Linked Image] 

[Linked Image]

[Linked Image]  

Last edited by Sandbagger; 08/02/19 09:19 AM.

[Linked Image]

Alienware Aurora R5
Windows 10 64 bit
Intel i7-6700K 4.2Ghz
Two GTX 1080 Foundations in SLI (8 Gig each)
32 Gig DDR4 2133Mhz
1TB SSD boot drive - 1TB SATA storage drive
5.1 Surround Sound
34" Dell Ultra Sharp U3415W (3440x 2440)
CH Pro-Pedals, Stick and Throttle
TrackIR-5 Pro