Previous Thread
Next Thread
Print Thread
Rate This Thread
Hop To
Page 27 of 27 1 2 25 26 27
#4455602 - 01/01/19 04:01 AM Re: 3D printed replica parts for Flight Sims :) ***** [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
PS Spitfire single type lever Fuel Cock is up now.Will work out lever next.
https://www.shapeways.com/product/X...?optionId=82279681&li=shop-inventory

Inline advert (2nd and 3rd post)

#4456039 - 01/04/19 12:17 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2014
Posts: 31
Nails Offline
Junior Member
Nails  Offline
Junior Member

Joined: Apr 2014
Posts: 31
Wilts, UK
Spitty!

This years BoB Mess dinner display is going to rely on you!

Can you print a 1:1 Hawker Hurricane front cockpit canopy frame? I don't have a photo to hand, but its the frame that holds the armoured front glass (with the gunsight behind it).

I want to display my full real Hurricane instrument panel, attached to a sort of half a front cockpit bit, that would be able to sit on a table. With the bottom of the instrument panel where the cockpit would end IYSWIM?

I will try and get a photo of what I'm waffling on about after work this evening. But first, I wanted to know if you could print the front canopy frame or not.

Cheers shipmate.

#4456339 - 01/06/19 10:02 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Ive done the Spitfire windscreen armoured glass holder so the Hurri one will work.I did it in 4 pieces to fit it on my printer though.That ok?Will need a pretty accurate sketch.

#4456792 - 01/10/19 07:03 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2014
Posts: 31
Nails Offline
Junior Member
Nails  Offline
Junior Member

Joined: Apr 2014
Posts: 31
Wilts, UK
Originally Posted by 453Raafspitty
Ive done the Spitfire windscreen armoured glass holder so the Hurri one will work.I did it in 4 pieces to fit it on my printer though.That ok?Will need a pretty accurate sketch.

Thanks for the reply.

Spitfire spares want £2500 for their tatty one. Unfortunately out of my price range.


Here are some photos. This is all I have. It is the front canopy section I want.

I want to mount my real instrument panel in a half round cockpit. Probably with just enough room to mount the P8 compass. The nose section just going past the front cockpit frame.

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

Thanks for taking a look. See Robert Stanford Tuck in his Hurricane? I managed to get his flying log book last year!

#4456879 - 01/11/19 08:13 AM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Awesome.Thanks..Here is what Ive found.Will CAD it up for you.

Attached Files Hawker-Hurricane-Original-Blueprint-Plans-WW2-period-archives-_57.jpg
#4457332 - 01/14/19 11:56 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
The windscreen is all sheetmetal apparently from a querie I put up to the experts.

#4458363 - 01/23/19 11:17 AM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Catching up on some printing.Spitfire cockpit lamps.

Attached Files lamp.jpglamp1.jpglamp2.jpg
#4465307 - 03/13/19 09:49 AM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Well that aint gonna work..Getting back on redoing some pit plans.This one is for the Fw190 from CheckSix
http://www.checksix-forums.com/viewtopic.php?t=121928
Loft is off original plans.Some resizing is needed wink

Attached Files Fw190 pit.jpg
#4465387 - 03/13/19 05:46 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Nov 2001
Posts: 3,689
Sokol1 Offline
Senior Member
Sokol1  Offline
Senior Member

Joined: Nov 2001
Posts: 3,689
Internet
Originally Posted by 453Raafspitty
Work on the P51 throttle continues..Small reworking on the threaded bushes for the Prop and Mixture friction locks on the front of the plate.Wheel tightens shims against handle and the front T knob locks it up.Prop and Mix handles are next to build also working out the K14 change mechanism on the throttle handle.


Are players interest in P-51 throttle grip/knobs for fit in Saitek/CH Quadrant, GVL224 throttle bases.

#4465420 - 03/13/19 09:43 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Its just 2 knobs (prop pitch and mixture) and the K14 twist handle if you want to go that way..

#4467975 - 03/28/19 09:55 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Fw190 design progress.

Attached Files Pitwip3.jpg
#4468402 - 04/01/19 11:51 AM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
More frames in place.

Attached Files Pitwip4.jpg
#4470218 - 04/12/19 10:29 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
The upper instrument panels been a real PITA..Fw190 pit WIP..

Attached Files WIP.jpg
#4473113 - 05/05/19 11:03 PM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Have started printing these off and selling them if anyones interested.

Attached Files 59590092_391963038198145_3323134458839695360_n.jpg58818422_603850303447365_6840759124335001600_n.jpg
#4473603 - 05/10/19 09:44 AM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Late model P51D gunsight bracket with K14 coming together.

Attached Files 59875748_2181781558580208_3811876809134309376_n.jpg59793600_451734888908945_2111992383317999616_n.jpg59756768_358274938148658_5207787862333849600_n.jpg
#4475033 - 05/22/19 07:25 AM Re: 3D printed replica parts for Flight Sims :) [Re: 453Raafspitty]  
Joined: Apr 2004
Posts: 3,779
453Raafspitty Offline
Senior Member
453Raafspitty  Offline
Senior Member

Joined: Apr 2004
Posts: 3,779
Australia,Sandstone Point
Set of B17 throttle handles made out of aluminium.

Attached Files 60412500_392512901348517_2698237264395239424_n.jpg60390633_335201780500939_6382656697067896832_n.jpg
Page 27 of 27 1 2 25 26 27

Moderated by  RacerGT 

Quick Search
Recent Articles
Support SimHQ

If you shop on Amazon use this Amazon link to support SimHQ
.
Social


Recent Topics
Its getting Real Now
by JimK. 06/23/19 04:32 PM
Danger Close
by reconmercs. 06/23/19 04:19 PM
"The Wolf's Call"
by THX-1138. 06/23/19 05:05 AM
VR unexpected results
by DM. 06/22/19 03:56 PM
MLB season so far
by PanzerMeyer. 06/22/19 02:32 PM
More UFO's Being Reported by Military Pilots
by Haggart. 06/22/19 10:32 AM
I thought Ozzies were tough
by KraziKanuK. 06/22/19 07:27 AM
Classical Latin
by PanzerMeyer. 06/21/19 09:54 PM
Happy Birthday Timothy
by Nixer. 06/21/19 01:40 PM
Copyright 1997-2016, SimHQ Inc. All Rights Reserved.

Powered by UBB.threads™ PHP Forum Software 7.6.0