#4159381 - 08/19/15 07:17 PM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Dec 2009
Posts: 749
AndyB
Member
|
Member
Joined: Dec 2009
Posts: 749
Ayrshire, Scotland
|
Hi Aqua, Sorry, bad labels. I didn't mean you'd get an output while both inputs were on. I was just labelling them as three different outputs that could be "ON".
I don't think the logic based system would work directly with a column/row setup.
You could use the +5v output to switch small relays each of which was across a different column/row combination, but that's making it a lot more complicated.
Cheers,
Andy
Last edited by AndyB; 08/19/15 07:20 PM.
|
|
#4159394 - 08/19/15 08:10 PM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Dec 2009
Posts: 749
AndyB
Member
|
Member
Joined: Dec 2009
Posts: 749
Ayrshire, Scotland
|
Hi Aqua, I've drawn up a wee circuit in case you want to go ahead with the switches you have. The component values shown are approximates but should work. Diodes across the coil of the relays are to protect them. Transistors are just cheapy switching ones. I've built similar circuits to this in my own pit and they seem to be quite stable. C1, R1, R2 and R3 would be the column and rows on your interface board. Hope this helps you along. Cheers, Andy
Last edited by AndyB; 08/19/15 08:10 PM.
|
|
#4159419 - 08/19/15 09:56 PM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Nov 2001
Posts: 3,955
Sokol1
Senior Member
|
Senior Member
Joined: Nov 2001
Posts: 3,955
Internet
|
Too much complication... I think the issue is: in G-940 the MODE switch is a slider switch ON-ON-ON, so need be replaced with a toggle switch ON-ON-ON, not a ON-OFF-ON. And, since the G-940 was be modded with another controller, what is expected from this MODE switch? In Cobra M5 the MODE switch just change the 7 joystick buttons number: MODE 1 = Buttons 1 - 7 MODE 2 = Buttons 8 - 15 MODE 3 = Buttons 16 - 22 Or is to became a kind of "shift1", "shift2", "shift3" button?
|
|
#4159687 - 08/20/15 08:08 PM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Jul 2015
Posts: 13
Vindicore
Junior Member
|
Junior Member
Joined: Jul 2015
Posts: 13
|
Hey guys I have my encoder all wired up correctly (I think!) however whenever I rotate it in a single direction it comes up as both button presses?
Also I do not understand what to do with the encoder section of the software which may have something to do with my problem!
Edit: It's because I forgot to put the diodes in, isn't it? *Sigh*
Last edited by Vindicore; 08/20/15 09:09 PM.
|
|
#4164628 - 09/03/15 11:13 AM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Aug 2015
Posts: 68
Debolestis
Junior Member
|
Junior Member
Joined: Aug 2015
Posts: 68
Croatia
|
What is DZ low and high? Is it like Dead zone and saturation in DI Viewer? What is Spec. Functions in Joystick axes? Also is it possible to make things bigger, MMjoy2 screen is to small. This is how it looks at my computer: I would like to translate MMjoy2 to Croatian language. Do I need to translate .lng file? Thank you!
|
|
#4164652 - 09/03/15 12:18 PM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Nov 2001
Posts: 3,955
Sokol1
Senior Member
|
Senior Member
Joined: Nov 2001
Posts: 3,955
Internet
|
I would like to translate MMjoy2 to Croatian language. Do I need to translate .lng file?
Yes, just translate this file (from one language available, Russian, English...) and save as Croatian.lng
|
|
#4164776 - 09/03/15 04:49 PM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Jan 2014
Posts: 274
mega_mozg_13
Member
|
Member
Joined: Jan 2014
Posts: 274
BELARUS, Minsk
|
I would like to translate MMjoy2 to Croatian language. Do I need to translate .lng file?
Yes, just translate this file (from one language available, Russian, English...) and save as Croatian.lng and send it to me =)
|
|
#4167935 - 09/12/15 07:32 AM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Sep 2015
Posts: 7
Bosk666
Junior Member
|
Junior Member
Joined: Sep 2015
Posts: 7
|
First of all I wanna say a big thank you to mega_mozg_13. This is a great tool to build diy controllers. Installing the drivers of the arduino boards was easy. updating the firmware was a little bit tricky . joysetup 20150606 is running fine. i tried newer version but when i want to load the config from the device i get errors. crc .... i am using win7 i found a solution. date of firmware and date of software must be the same. now everything is working
Last edited by Bosk666; 09/12/15 03:01 PM.
|
|
#4168292 - 09/13/15 02:35 PM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Sokol1]
|
Joined: Aug 2015
Posts: 68
Debolestis
Junior Member
|
Junior Member
Joined: Aug 2015
Posts: 68
Croatia
|
Anybody get this to work? PS3 hall sensor thumbstick. I can send one to you mega_mozg_13, so that you can see how to connect it. I also finished Croatian translatio for MMJoy2, where shall I send it?
|
|
#4168565 - 09/14/15 11:59 AM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Debolestis]
|
Joined: Jan 2014
Posts: 274
mega_mozg_13
Member
|
Member
Joined: Jan 2014
Posts: 274
BELARUS, Minsk
|
Anybody get this to work? PS3 hall sensor thumbstick. I can send one to you mega_mozg_13, so that you can see how to connect it.
you can try to link it with MCP3202 and select "KMZ60+MCP3202" type sensor.
|
|
#4169486 - 09/16/15 03:49 AM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Czary]
|
Joined: Jan 2014
Posts: 274
mega_mozg_13
Member
|
Member
Joined: Jan 2014
Posts: 274
BELARUS, Minsk
|
Next thing that interests me a lot - is it possible to drive small servo or tiny stepper motor using values from War Thunder output or any other sim ?
next step is output data to "MAX7219 7-segment 8-Digits" link "small servo" or "tiny stepper" maybe later =)
Last edited by mega_mozg_13; 09/16/15 03:50 AM.
|
|
#4171379 - 09/21/15 07:29 AM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Czary]
|
Joined: Jan 2014
Posts: 274
mega_mozg_13
Member
|
Member
Joined: Jan 2014
Posts: 274
BELARUS, Minsk
|
Now I have freezeing axis problem again- I need to restart the device in MMjoy2 to work. fixed. wait for next update(few days).
|
|
#4171380 - 09/21/15 07:30 AM
Re: MMJoy/MMjoy2 - Build your own USB controller
[Re: Bromius]
|
Joined: Jan 2014
Posts: 274
mega_mozg_13
Member
|
Member
Joined: Jan 2014
Posts: 274
BELARUS, Minsk
|
Is it possible to implement I2C in the firmware? In particular for supporting Wii nunchuck. $10 nunchuck gets you a 3 axis accellerometer, 2 axis analog stick, and 2 buttons. As it sits, I think I need to build a bridge with a second mcu. no. nunchuck link with Bluetooth to PC...
|
|
|
|