I've ordered your boost cut-out "tit" from Shapeways. If you make amendments what version do I get sent?

I've also got someone removing their boost cut-out from their real life Hurricane, so we can get measurements and pics. More to follow ....

As I have already said. Thanks for doing this stuff. A fair dinkum Sheila-Bruce. Cheers.

You will be getting the updated model
That will be ideal,thank you.
No worries,I know how hard it is to get "real" parts these days so make it a mission to help out others.

For Spitfire guys..Kigass primer body.
https://www.shapeways.com/product/GV8ZF93JU/kigass-body?key=b721863ba7d1cc180f1e33163e1bc1b2

Now up,Spitfire trim wheel covers,later model cockpit ventilator and dimming screen pull ring bracket at the shop
https://www.shapeways.com/product/8VX6ERC2F/spitfire-ventilator-later-type

For WW1 fliers is the British Pocket Watch holder that sits on the instrument panel.
http://www.shapeways.com/product/2BML6AP29/watch-holder?li=shop-results&optionId=57123230

Another WW1 part,British Magneto switches and base arriving soon
..

Are Spitfire spade brake lever in Shapeways?

Searching Spitfire dont list: http://www.shapeways.com/search?q=spitfire&s=0#more-products

Hello
I have been following your thread for quite a long time and am impressed what you are constructing here so.
I have seen that you have a made ME 109 Throttle housing, but still no thumb switch;-)
I once surveyed my thumb switch (a cast of an original) and recorded, maybe you want to offer in your shop him yes.

With best regards

Translated with Google

Thanks guys.Will look forward to a long night tonight!Not sure if I have a brake handle in my stash but will check.Can do the throttle handle easily Carh451 thanks.Do you need a copy yourself?

Getting there..

I think this channel should by more width than 12mm, the lever/rocker has 12,7mm and need fit inside then...

http://s2.postimg.org/ub4cewnbd/gashebel_2.jpg
http://4.bp.blogspot.com/-xYD2bewpjZ8/U6PxyonglwI/AAAAAAAAAJ0/I3jwshhq3Nc/s1600/IMG_7761.JPG
http://4.bp.blogspot.com/-1FMx2PGRsX8/U6PxzPDHrHI/AAAAAAAAAJ8/5_sRX9TNgtw/s1600/IMG_7766.JPG

I measured it again, the groove is below 12mm and then wider. Before the start of the radius there are 13 mm in width, the width at the end of the radius is 16mm. I think it should be a radius of 0.75?
As in the photo is the thumb rocker not to the bottom of the groove.
The groove on the back of the thumb rocker is 8mm deep.
I say again that I only a Resin - cast of a thumb switch have! I think there will be no differences 1mm, but certainly some variation.
I would like a copy of it, because I want to build a ME 109 lever for my HomeCockpit me.
For the cockpit I will still continue to require components from your shop. :-)

I am sending you a few pictures in an email ..

453Raafspitty, when you're ready, send me the model and I'll run a test part before you ship it off to Shapeways.

carh451, could you send me the reference photos as well?

tnx.

g.

Working on it...

Now up,Spade grip brake handle and also crowbar ends to suit the Spitfire Cockpit doors.You will need a tube .8" (22mm) dia by 12" (305mm) long.Also added are the Cockpit door handle latches and handle.If anyone needs a door let me know as I,m tooling up to reproduce them.
https://www.shapeways.com/product/TNM3EC...c8e3dc1860c0202
https://www.shapeways.com/product/BRUD68...9415463ec8c97ae

For flying at height in your Spitfire you will need one of these.

https://www.shapeways.com/product/BBBS37YSK/oxy-regulator-cover?key=f37538c0bf6730dc7aa7eea79121e9d0

carh451, Can you tell me how wide the "back half" is that's attached to the throttle arm?

Here's what I've done so far:

The screw holes are sized for a 1-3/4", #8-32 socket head cap screw. The screw is probably a bit on the long side.

Sokol1, do you have any pics of that throttle quadrant from the back side? What about better pics & dimensions for the mixture knob?

tnx!

g.

Here's a much better render:


g.

http://s30.postimg.org/qotap23sx/gashebel_1.jpg
http://s30.postimg.org/9pkc9ssld/Gashebel3.jpg
http://s30.postimg.org/s6er0m8jl/Gashebel21.jpg
http://s30.postimg.org/e18xyszi9/Gashebel_Fw_190_D.jpg

The drawing is for latter war Fw 190 D or TA, the design was simplified relative to early Fw 190 versions.

For the mixture I dont know, the best pictures that I see is these that I link in previous post.

(Looks like a missed an umlaut for the "coarse" label...)

Thanks for the pics Sokol1. From the last photo linked, I'm going to guess the back half of the throttle grip is around 30mm.

The lettering is probably going to look better as a decal as it would take a VERY long time to print that part with a .35mm nozzle.

g.