I am no longer using any CPU speed control utility, and thats for any of my PCs:
AMD-mil64-2.5 Ghz, P4-2.4 Ghz, P4-HT-3.0Ghz, P4-HT-3.4Ghz, D2C-2.18Ghz

We used to use this throttle down method before this Glide wrapper, but it is no longer necessary
unless you run D3D and not Glide 3Dfx graphics and wrapper.

If you use the DGVOODOO wrapper and set it up as we recommend via the REFRESH settings,
the game world rate will be limited to the monitor's refresh rate (60, 65, 70 hz) and
thus you dont need to throttle down your CPU.



Note also, when you play multiplayer and share a common cockpit (pilot/cpg) get both players to
run the same monitor refresh rate (60hz or whatever) to reduce the amount of visable update blinking
and close up formation winking out of the other a/c when very close.

Hi - I'll not create a brand new discussion for this, but instead, place it in here. I would like to thank everyone that's worked so hard on making this game playable again on updated systems. From the install guides to the graphics tweaks, you all are to be commended. Thank you, very much.

Using the tweaks in this thread, I'm amazed that LB2 looks like it does. IMO, it's as good, maybe even better, than when I played it using my Voodoo3. (Could be my imagination.. )

Thanks again everyone for your work and time in showing others how to pump life back into this wonderful game.

KK

*EDIT* I forgot to post my computer specs, just in case they can help someone else. Not the best system in the world, but it does what I want it to.. most of the time..

PIII 750MHz
1GB RAM
GeForce Ti 200 64MB
Sidewinder Precision 2 joystick
On board sound (have an Audigy card that I'm going to install soon)

The appreciation is always nice!

hi

i gave up on LB1 and install LB2 but i can not find LB2Cfg.exe anywere i look on the 2 cd´s and in dir were the game install.
i use the big install.

Thanks

Chaos, I believe you only get that file when the Display DirectDraw Update (DDU) patch is installed. It doesn't hurt anything (iirc, it was for D3D improvement and we normally use the Glide approach) to install it in my experience, and you get the config utility which is easier to use than going into an ini and change the file or whatever it is.

http://www.speichts.com/games/lb2/basic_install.html

Chaos, if you haven't used this site for installation guidance, it's superb (with thanks to +G).

thanks now iam in the game and can see the chopper, now i will test more to see if its stable.

thanks again for u help

New Apps Note;

Now days I have LB2 running on a QuadCore/Vista32 and a Dual2Core/WinXP-SP2.

When I was setting up LB2 on the WinXP rig, for some reason LB2 would
- have UI sounds, but none in the 3D or 2D world/Cockpit
- crash upon exit

What I found out by trial and error, was I had DX9 selected instead of DX7 in DGVooDooSetup.
Apparently for my rig, at least, LB2 likes DX7 better. Yes, I know thats what on the picture
above that I posted, but for some reason I tried DX9 for grins. It seems to matter.

Thats it for now. Keep em flying and hovering

My Longbow2 rig has a Voodoo3 2000 PCI card in it. I can run it fine at the default resolution but, when I try to follow the DGVoodoo 1.50Beta wrapper setup, I lose my cockpit. Anyone know if the wrapper works with an actual voodoo card or should I get another card if I want 1600x1200 res on a 20" monitor?

Thanks!

EDIT:

Also, does this issue...

"If you're using Windows 95/98/ME and your have more than 366MB of RAM installed on your PC, you'll probably need to adjust your maximum Windows memory settings as well."

Include video ram too? I have 192 sys ram, if my vid card has 128 and I bump my sys ram to 256, will that cause problems?

Thanks!

New Longbow2 box specs:

Win 98 SE/DX7
P3 1000 Mhz
192 Meg PC100 SDRAM
GeForce FX5200 128MB AGP
SB Live

So, I am up and running at 1600x1200 with the wrapper. However, I now have corrupt videos and stuttering in game.

Are there any further tweaks to fix these issues?

Thanks!